Harvia Fenix Wi-Fi Digital Sauna Heater Control Kit | FX30 / FX45 / FX30C Combi
- 4.3-inch glass touchscreen panel for Harvia heaters with separate control
- Wi-Fi monitoring in Harvia's MyHarvia app
- FX30 and FX45 for Virta, Cilindro Half, Spirit and Club; FX30C for Virta Combi
- Description
- What's Included
- Specifications
- Documents
- Warranty
What is the Harvia Fenix sauna control?
The Harvia Fenix is a sauna control with a 4.3-inch glass touchscreen panel and Wi-Fi, for Harvia electric heaters that have no controls of their own. Topture sells four models: the FX30 and FX45 (FX30-U1-U3-XC, FX45-U1-U3-XC) for Virta, Virta Pro, Cilindro Half, Spirit and Club heaters, and the FX30C Combi for Virta Combi heaters, in a 240 V single-phase (FX30C-U1-XC) and a 208 V three-phase (FX30C-U3-XC) version. Each comes with a power unit, a data cable and a heater sensor; the FX30C adds a humidity sensor.
The temperature can be set on the Fenix from 104 to 194°F (40–90°C). Its Wi-Fi gives monitoring in Harvia's MyHarvia app: the heater's status, the sauna temperature and the remaining heating time. Harvia says the Fenix interface learns the heater's performance, and it offers three presets, Mild, Cozy and Hot. The FX30 and FX45 share their ratings with the Harvia Xenio CX30 and CX45; the difference is the glass touchscreen panel.
Which Harvia heaters does each Fenix model run?
The Harvia Fenix models run the Harvia heaters below. "Two supply circuits" means the heater is wired to the power unit as two groups, two separate supply circuits, as the heater's manual shows.
| Fenix FX30 | Fenix FX45 | Fenix FX30C Combi | |
|---|---|---|---|
| Virta 6 kW (HL60E) | Yes | Yes | No |
| Virta 8 kW, 9 kW or 10.5 kW, 240 V | Only on two supply circuits | Yes | No |
| Virta 10.5 kW, 208 V three-phase | Yes | Yes | No |
| Virta Pro 16 kW | With the LTY45, on four supply circuits | Yes on two supply circuits; with the LTY45 on four | No |
| Virta Pro 20 kW (208 V three-phase) | With the LTY45 (required) | With the LTY45 (required) | No |
| Cilindro Half 6 kW | Yes | Yes | No |
| Cilindro Half 8, 9 or 10.5 kW | Only on two supply circuits | Yes | No |
| Spirit 6 kW | Yes | Yes | No |
| Spirit 8 kW or 9 kW | Only on two supply circuits | Yes | No |
| Club 10 kW | 208 V yes; 240 V only on two supply circuits | Yes | No |
| Club 12.5 or 15 kW | No | Yes; 240 V only on two supply circuits | No |
| Virta Combi 8 kW, 9 kW or 10.5 kW, 240 V | No | No | FX30C-U1-XC |
| Virta Combi 10.5 kW, 208 V three-phase | No | No | FX30C-U3-XC |
| KIP with separate control | No | No | No |
The Harvia LTY45 power extension (sold separately) works with the FX30 and FX45, and the Virta Pro 20 kW always needs it; the FX30C needs no power extension for any Virta Combi. Harvia's KIP heaters with separate control run from the Harvia Xenio CX170, not the Fenix.
Where does each part of the Fenix go?
The Fenix power unit goes on a wall outside the sauna room, in a dry place above 32°F (0°C); it must not be recessed into the wall. The glass panel can be surface- or flush-mounted, inside the sauna room or in a bathroom or living area. The heater sensor goes where the heater's manual shows. Harvia's manual says only an authorized, professional electrician may make the electrical connections. Your licensed electrician sizes the breaker and wire from the manual that ships with the heater and your local code. Harvia's installation manual, under Documents, gives the exact wiring and sensor positions.
What's in the box with the Harvia Fenix?
- Fenix glass touchscreen control panel with Wi-Fi
- Power unit
- Data cable, 16.4 ft (5 m)
- Heater sensor with an overheat protector, on a 13 ft (4 m) cable
- FX30C Combi models only: bench sensor for humidity and temperature, on a 13 ft (4 m) cable
- Installation material
- Installation instructions
What you need separately
- A Harvia heater with separate control from the table above
- The circuits and wiring, installed by a licensed electrician
- The Harvia LTY45 power extension (FX30 and FX45 only), only for the Virta Pro 20 kW, or the Virta Pro 16 kW wired on four supply circuits
- Optional: a sauna light and a fan, which the Fenix can switch
The sauna heater controls collection has Harvia's Xenio controls and the other controls Topture sells.
Harvia Fenix specifications
| FX30-U1-U3-XC | FX45-U1-U3-XC | FX30C-U1-XC | FX30C-U3-XC | |
|---|---|---|---|---|
| Supply | 240 V single-phase or 208 V three-phase | 240 V single-phase or 208 V three-phase | 240 V single-phase | 208 V three-phase |
| Heater load, 240 V | 7 kW on one supply circuit, 11 kW on two | 10.8 kW on one supply circuit, 17 kW on two | 12.7 kW on two supply circuits | — |
| Heater load, 208 V three-phase | 10.5 kW | 15 kW | — | 10.8 kW |
| Steamer | — | — | Up to 2.1 kW | Up to 2.1 kW |
| Net weight | 7.8 lb | 8.2 lb | 8.2 lb | 8.4 lb |
| Temperature setting | 104–194°F (40–90°C), set on the Fenix panel |
|---|---|
| Wi-Fi | Built in; monitoring in Harvia's MyHarvia app |
| Control panel | 4.3-inch glass touchscreen; 3.66" W × 0.79" D × 5.16" H; surface- or flush-mounted |
| Power unit | 14.3" W × 2.9" D × 10.5" H (364 × 73 × 267 mm); mounts outside the sauna room |
| Power extension | LTY45 for the FX30 and FX45, sold separately; needed only for the Virta Pro 20 kW, or the Virta Pro 16 kW on four supply circuits |
| Warranty | 2-year manufacturer warranty; the extra year Harvia gives registered electric heaters does not apply to control units |
